Verex Monitor ISM Guide d'installation télécharger pdf (Page 11)

21-3601E rev1.3 xL Simplified Installation Guide 5

North American Modem

(Bell 103, 300 baud)

For Director Software Communications to Feature set 3

World Wide Modem (2400 baud)

For Director Software Communications to Feature set 7

CPU Failure available with main control module firmware 4.3 or

greater.

312 4

Seized Tip

Seized Ring

Tip

Ring

Off Hook

LED

Turns on when

unit dialing out.

Plugs into xL Main Control Board

Modem Expansion Socket

North American Modem

312 4

Seized Tip

Seized Ring

Tip

Ring

Off Hook LED

Turns on when

unit dialing out.

Plugs into xL Main Control Board

Modem Expansion Socket

World Wide Modem

756 8

Line Failure

9312 4

Output 8

Output 7

Output 6

Output 5

Output 4

Output 3

Output 2

Output 1

To REDCARE Unit

2 vertical Jumpers in 1+2 = Output 8 will be 12VDC

high from 0V if main control board CPU fails

2 vertical Jumpers in 2+3 = Output 8 will be 0V low

from 12VDC high if main control board CPU fails

1 Jumper in 1+2 on left side =

Output 8 is a standard output #

8 on this board.

CPU

Failure

with

REDCARE

Interface

From REDCARE Unit

See “ENABLE LINE

FAILURE” this page.

NOTE: Bell 103 and World Wide Modems will call Director Software manually to their Feature Set limitations above. An external

modem must be used for Director communications above Feature set 7. An external modem connected to the main control module

can not call Director. See the previous Main Control Module detail. Director can call the main control module and maintain a “stay

connected” send and receive session using an external modem. Alarm reporting is not possible with an external modem. Alarm

reporting is only done with Bell 103 and WW Modems or IP to SIP.

Feature Expansion Board

Required for Access Control in any feature set.

Feature Expansion Board

Feature Expansion Socket

Plugs into xL Main Control Board

Memory Expansion Socket

WW Modem “CPU Failure” available with main control module firmware 4.3 or greater.

CPU Failure (WW Modem)

Output 8 must be programmed as “System Fault” in System Outputs. Use Director Software outputs or Simplified or Advanced

(B000:00, System Outputs #56) keypad programming. For a negative to positive output, it can be left defaulted. For a positive to

negative output, it must also be programmed to be inverted.

ENABLE LINE FAILURE on WW Modem

This feature is used to monitor for line faults from switched communicators such as Redcare

NOTE: The WW Modem must be plugged into the main control module.

Simplified Configurations:

Comms (Communications) Configure Group

– Enable Line Failure: Default: No

(UK ACPO = 9yes)

– Line Fail Polarity: Positive 12VDC going to Negative 0V or Negative 0V going to Positive 12VDC. Default: Positive

Advanced Configurations: S005È03

– Field 2: Parallel STU 8OP Supports Line Fail: 9(yes) □ (no) Default: no

(UK ACPO = 9yes)

– Field 3: Parallel STU 8OP Line Fail Negative Polarity: 9(yes) □ (no) Default: no = Positive Polarity

Notice: Use minimum 26AWG UL/CSA/or

equivalent approved telephone cable.

1 2 ... 6 7 8 9 10 11 12 13 14 15 16 ... 33 34

Commentaires sur ces manuels

Pas de commentaire

Verex Monitor ISM Guide d'installation Page 11

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Verex Monitor ISM