Verex Monitor ISM Guide d'installation télécharger pdf (Page 9)

21-3601E rev1.3 xL Simplified Installation Guide 3

Main Control Module

NOTE: Any expansion modules used with the xL system, like the 8 and 16 Point Expanders, can also be used on the xL Main

Control Unit, Module Bus (SNAPP).

Mounting a Control Box

On Dry Wall Use 1/8” hollow wall, expansion anchors (p/n 331-8755). Unscrew the screws from the anchors. Hold the control box

on the mounting surface. Mark the mounting holes. Force a starter hole in each mark with a sharp tool e.g. a screw driver with a

small, flat edge. Hammer the anchors into each hole. Align the box mounting holes over the anchor holes and screw in the anchor

screws until tight.

On Concrete Surface

Hold the control box on the mounting surface. Mark the mounting holes. Use a hammer drill with a 3/16”

carballoy drill bit and make 1” deep holes in each marking. Insert a # 6-8 plastic anchor (p/n 331-8470) in each hole and hammer

them in. Use # 8 X 1”, Phillips, wood screws (p/n 738-2169) to screw into the plastic anchors and mount the box.

Control Box Dimensions (height, width, depth)

North American Main Control Unit 573-6801: H355mm x W254mm x D86mm (H14” x W10” x D3, 3/8”)

Main Control Unit with 230V transformer (European) and IPSU (intelligent power supply unit) Expander 573-2912:

H470mm x W305mm x D89mm (H18, ½” x W12” x D3, ½”)

Input Expander 573-4714

: H259mm x W203mm x D76mm (H10, 3/16” x W8, 1/8” x D3”)

MAIN CONTROLLER METAL ENCLOSURE

WITH 230 VOLT TRANSFORMER

573-2912

Main Control Board

Battery

cable plug

Position

battery with

terminals on

left

Battery bracket mounting holes for 17Ah

battery bracket 232-2606. Order kit 250-3617.

7Ah battery bracket 232-2605 from supplied

accessories kit. Mounted on 7Ah battery.

312

TB2TB1

312 312 312 12 312 312 312 312 312 312312

312 4 312 4

TB3TB4TB5TB6 TB7TB8TB9TB10TB11TB12

TB13

TB14

Spare fuse

Fuse in use

Fuse tray

Terminal block screw holes cover (353-2004).

230 Volt Transformer

Replacement fuse: ½ AMP

fast blow p/n 342-0005

Once electrical wiring is complete, obtain

cover from supplied accessories kit and

plug on fuse block screw hole assembly.

Fuse block (353-2003)

Electrical

Ground

Procedure for Cold Booting the Main Control Board and Clearing Memory

1. Remove all power from main control board.

2. Insert the Program Reset Jumpers (CFG0 and CFG1) horizontally. See Program Reset Jumpers on the right side of the main

control module in the “Main Control Module” diagram.

3. Apply AC Mains power.

4. The Status and Trouble LEDs will flash on and off together slowly.

5. Remove the 2 jumpers.

6. The same LEDs will momentarily flash rapidly together. (Controller processing)

7. The trouble light will turn off and only the Status LED will flash rapidly.

8. Proceed through the following “

Powering on the System for the First Time and Understanding How to Program the

System Using the LCD Keypad” section

9. The keypad will display regular screens and only the Status LED will flash slowly to indicate a normal condition.

10. The memory has been returned to factory defaults. Reconnect all power.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 33 34

Commentaires sur ces manuels

Pas de commentaire

Verex Monitor ISM Guide d'installation Page 9

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Verex Monitor ISM