Verex MONITOR AFx Guide de l'utilisateur télécharger pdf (Page 208)

202

MONITOR AFx™ Director V4.1 User's Guide

500-9041 v4.1

If you change any value for an elevator/lift, this will

cause that device to be reset to its default / scheduled

state (this allows configuration updates to be managed

properly). To check or re-set status aspects, refer to

the "Elevator" status/control topic.

Introducing Access-Controlled

Elevators

With access-controlled elevators, floor call-

buttons are disabled until an authorized person

presents their access card. When the card is

presented, the specific floors for that person

will become available.

Each system can include up to

elevators,

and a total of up to

124

access-controlled

floors.

Exception: The elevator capacity is shared with doors

(max. 32 combined). Doors also share the elevator

numbering (and panel memory space), and will be listed

along with the doors (editable under "Door" only).

Tip: You can define elevators at the end of the list, or

click

[Filter]

on the toolbar to show only the numbers

associated with elevators.

Panel/Firmware Revision:

Support for elevators and

controlled floor-access requires V3.0 panel firmware.

Recommended:

≥

V3.2

panel firmware, and

≥

V1.5

elevator controller firmware.

Feature-Set and Licensing: Support for elevators

requires a 'feature-set' selection of

or higher (via

Enterprise software licensing).

For details, refer to "Account-Wide Panel Settings", and

"Software Activation and Licensing".

Floor Wiring and Set-Up: Floor relays must be wired in

the same relative order for all elevators, and then

defined in the same order (such as lowest to highest).

To define system floors, refer to the floor configuration

topic (to follow).

The access-requirements for each elevator

reader can be configured to meet your specific

requirements. As well, many items can be set

to a rotating schedule, allowing different

parameters to be in effect after-hours.

For details on setting up the card/token format, refer to

"System Card-Access Settings".

Wiegand-output reader keypads are supported for

Card+PIN (and PIN-Only) entry modes and signalling

duress. Matrix-style keypads (i.e., that require

additional connections) are

not

supported for elevators.

Accessing the Elevator Configuration

Topic

(Multi-

Account

Systems: Click

[Account Folders]

the 'tree', and locate and double-click the desired

account.)

Select

Elevators

from the MyTools bar,

click your site/account button in the tree, open

"Configuration" (

), and select

Elevators

(Under the specific panel group and panel--if

listed in the 'tree'.)

Panel Groups and Panels: The 'tree' can be set to

show configuration topics in a single list (logical tree

view), or on a panel-by-panel basis (best for multi-panel

systems). For details, refer to "Other Desktop

Choices".

Adding an Elevator to the System

(Before adding an elevator, the applicable elevator-

controller module should be set up. For details, refer to

"Expansion Modules".)

Access "Configuration Elevators" as

described previously, and use the

Grid

Form

toolbar-button to select your preferred 'view'.

Forms view: Details for one door at a time;

Grid View: All defined doors in a list.

Now, click

[+]

at the bottom of the form, or

right-click the form, and select

Add New

from

the pop-up menu.

Alternative: You can also select a blank/grey item from

the list (Forms view: bottom of the window). If no grey

ones are listed (or the form is blank), click

Filter

on the

toolbar, and re-check the listing.

Now, refer to the selection-descriptions for this

portion of the elevator screen while entering

and/or selecting your desired settings.

Tip:

Start with the 'Standard' tab, and then view any

additional topics of interest.

Tip:

You can copy all settings for an elevator, and

paste them into another one: Right-click the 1

one (a

blank area if in 'Forms' view), and select

Copy

. Then,

select a blank/new elevator from the list, right-click

again, and select

Paste

. After 'pasting', change the

name and any settings as desired.

Note:

'Copy' and

'Paste' are also available from the

dit

menu.

Elevators (Lifts) and Associated Readers

1 2 ... 203 204 205 206 207 208 209 210 211 212 213 ... 323 324

Verex MONITOR AFx Guide de l'utilisateur Page 208

Commentaires sur ces manuels

Verex MONITOR AFx Guide de l'utilisateur Page 208

Commentaires sur ces manuels

Produits connexes et manuels pour Systèmes de contrôle d'accès de sécurité Verex MONITOR AFx